Technology · Optional add-on

Add UV disinfection to any Purus.

Purus filters the water clear. An optional UV disinfection reactor, fitted after the Purus outlet, then inactivates the bacteria and viruses that remain. Two independent barriers, run by one control system, quoted as part of your Purus package.

How it works

Filter it clear. Then disinfect it.

A 72-second walk through the train: the Purus gel membrane, why clear water matters to UV, the UV reactor, the shared controls and how each Purus model is matched to a reactor.

Schematic animation, not to scale. Filtrate turbidity and UV transmittance shown are examples, not measured results. Prefer to step through it yourself? Open the interactive version.
Why filter first

UV works best on clear water.

UV light has to reach a microorganism to inactivate it. Suspended particles absorb and scatter the light, and a microbe sheltering behind or inside a particle can escape the dose. Putting Purus in front removes that shelter.

Barrier 1 · Purus

Physical removal

The gel membrane (approx. 10 nm size exclusion) holds back silt, colloids and most microorganisms, and lowers the turbidity of the water going to the UV reactor.

Barrier 2 · UV disinfection

Inactivation

A measured UV dose damages the genetic material of bacteria and viruses that pass the filter, so they can no longer reproduce. No chemicals are added to the water.

Together

Two different mechanisms

One barrier removes, the other inactivates. Because they work in different ways, the train does not rely on any single step performing perfectly.

Schematic: raw water is pumped through the Purus vessel, then through the UV disinfection reactor, then out as disinfected water
Raw water → Purus vessel → UV disinfection reactor → disinfected water. Schematic, not to scale.
What the option includes

One train, one control system.

The reactor is fitted on the Purus outlet and wired into the Purus controller, so filtration and disinfection start, stop and alarm together.

Reactor

UV disinfection reactor

316L stainless-steel reactor with a low-pressure UV lamp in a quartz sleeve and an internal flow mixer, so all of the water passes close enough to the lamp to receive the dose.

Monitoring

UV intensity sensor

A sensor on the reactor viewport reads the UV intensity continuously, so a dirty sleeve, an ageing lamp or a drop in water quality shows up before it becomes a problem.

Controls

Wired into Purus

The Purus controller switches the UV system on and off and receives its lamp-fail and low-UV-intensity alarms. Alarms can also be passed to your BMS.

Fail-safe

Outlet hold

If disinfection is not proven, the treated-water outlet is held rather than passing water that has not received its dose.

Schematic: the Purus controller linked to the UV controller for remote on/off, lamp-fail and low-UV-intensity alarms, UV intensity monitoring and outlet hold
The Purus controller and the UV controller share start/stop, alarms and the outlet hold.
Matching the reactor

A UV reactor for each Purus model.

UV reactors are sized to the peak flow through them and to the UV dose the application needs: 40 mJ/cm² for drinking and process water, 30 mJ/cm² for cooling-tower and other non-potable uses. The pairings below use the reactors’ rated flows at a UV transmittance of 85%, typical of town water. Purus filtrate is expected to be at or above that.

Purus model Design peak flow Drinking & process water · 40 mJ/cm² Cooling tower & non-potable · 30 mJ/cm²
Purus 20.1~1.5 m³/hRated to 1.81 m³/hRated to 2.41 m³/h
Purus 50.2~5.5 m³/hRated to 6.01 m³/hRated to 5.77 m³/h
Purus 100.5~8.5 m³/hRated to 9.01 m³/hRated to 10.02 m³/h
Purus 100.20~8.5 m³/hRated to 9.01 m³/hRated to 10.02 m³/h

Planning selection only. The final reactor is confirmed by Blue Quest engineering against a measured UV transmittance of your Purus filtrate, your peak flow and the dose your application or regulator requires. Multi-vessel installs and higher flows use larger or multiple reactors.

Good to know

Where UV adds the most.

Where it fits

Drinking-water and food and beverage process water, rainwater and bore supplies, washdown and reuse water, and cooling-tower make-up or recirculation where a microbial barrier is wanted.

What it doesn’t do

UV treats the water as it passes and leaves no residual disinfectant behind. Where water is stored or reticulated, a residual may still be required. Like Purus, UV does not remove dissolved salts or metals.

Looking after it

Lamp replacement and quartz-sleeve cleaning are added to your Purus service schedule, at the intervals recommended for the reactor.

Feeding a reverse osmosis plant?

Purus + UV ahead of RO.

The same two barriers take the particle, colloid and microbial load off RO membranes, without chlorine reaching them. See how the three-barrier train works and the evidence behind it.

See the RO train →

Add UV to your package.

Tell us in your enquiry and the reactor is quoted with your Purus package after we confirm your flow and water quality.